IMC Networks Computer Hardware McPc Gigabit User Manual

McPC-Gigabit  
(PCI Version)  
Operation Manual  
 
Table of Contents  
FCC Radio Frequency Interference Statement ....................................................ii  
Warranty............................................................................................................ii  
About the McPC-Gigabit ....................................................................................1  
AutoCross ..........................................................................................................1  
LED Indicators....................................................................................................2  
Specifications.....................................................................................................2  
IMC Networks Technical Support.......................................................................2  
Fiber Optic Cleaning Guidelines.........................................................................2  
Safety Certifications............................................................................................4  
iii  
 
About the McPC-Gigabit  
The McPC-Gigabit is a low-cost, IEEE 802.3 single-conversion, PC Card media  
converter that converts 1000Base-TX twisted pair to 1000Base-SX multi-mode or  
1000Base-LX single-mode fiber. The McPC-Gigabit is available with one RJ-45  
connector for the twisted pair port and a SC connector for the fiber port.  
The McPC-Gigabit is also available for single-strand which allows two individual  
channels to share one strand of fiber; Full-Duplex data travels on different  
wavelengths— 1310 nm and 1550 nm.  
The McPC-Gigabit can be mounted into any PC with a standard PCI and includes  
diagnostic LEDs for each port.  
Installing the McPC-Gigabit  
Offering plug-and-play operation, the McPC-Gigabit comes ready to install, utilizing  
power from the PC’s motherboard. To install the McPC-Gigabit:  
1. Turn off the PC  
2. Remove its cover  
3. Find an empty PCI slot  
4. Align the McPC-Gigabit in the slot  
5. Screw the McPC-Gigabit into the computer casing’s bracket  
6. Make sure the McPC-Gigabit does not extend past the edge of the case  
7. Attach the keyed mini-power connector to the McPC-Gigabit  
8. Attach the male end of the “Y” connector to one of the computer’s standard size  
power connectors  
9. Replace the cover  
10. Attach the cables between the McPC-Gigabit and the devices that will be  
connected  
AutoCross  
Whether you are using crossover or straight-through CAT5 twisted pair cabling,  
McPC-Gigabit will support both types of connections with AutoCross, a feature which  
automatically selects between a crossover workstation or Pass-Through connection  
depending on the connected device.  
FX  
TX  
1
 
LED Indicators  
Each McPC-Gigabit includes two LEDs, located on the RJ-45 connector.  
LED functions are as follows:  
FX LNK/ACT  
TX LNK/ACT  
Glows green when a link is established on the fiber port; blinks  
green when activity is detected on the fiber port.  
Glows amber when a link is established on the copper port; blinks  
amber when activity is detected on the copper port.  
Specifications  
Environmental  
Operating Temperature  
+32° to +104° F (0° to +40° C)  
Storage Temperature  
-4° to +158° F (-20° to +70° C)  
Humidity:  
5 - 95% (non-condensing)  
Input Specifications  
0.7A @ 5V DC  
IMC Networks Technical Support  
Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);  
+32-16-550880 (Europe)  
Fax: (949) 465-3020  
Fiber Optic Cleaning Guidelines  
Fiber Optic transmitters and receivers are extremely susceptible to contamination by  
particles of dirt or dust, which can obstruct the optic path and cause performance  
degradation. Good system performance requires clean optics and connector ferrules.  
2
 
1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from  
a reputable supplier; low-quality components can cause many hard-to-diagnose  
problems in an installation.  
2. Dust caps are installed at IMC Networks to ensure factory-clean optical devices.  
These protective caps should not be removed until the moment of connecting  
the fiber cable to the device. Should it be necessary to disconnect the fiber  
device, reinstall the protective dust caps.  
3. Store spare caps in a dust-free environment such as a sealed plastic bag or box  
so that when reinstalled they do not introduce any contamination to the optics.  
4. If you suspect that the optics have been contaminated, alternate between  
blasting with clean, dry, compressed air and flushing with methanol to remove  
particles of dirt.  
Electrostatic Discharge Precautions  
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or  
stand alone units, containing electronic components. Always observe the following  
precautions when installing or handling these kinds of products  
1. Do not remove unit from its protective packaging until ready to install.  
2. Wear an ESD wrist grounding strap before handling any module or component.  
If the wrist strap is not available, maintain grounded contact with the system unit  
throughout any procedure requiring ESD protection.  
3. Hold the units by the edges; do not touch the electronic components or gold  
connectors.  
4. After removal, always place the boards on a grounded, static-free surface, ESD  
pad or in a proper ESD bag. Do not slide the modules or stand alone units over  
any surface.  
WARNING! Integrated circuits and fiber optic components are  
extremely susceptible to electrostatic discharge damage. Do not  
handle these components directly unless you are a qualified service  
technician and use tools and techniques that conform to accepted  
industry practices.  
3
 
Certifications  
CE: The products described herein comply with the Council Directive on  
Electromagnetic Compatibility (2004/108/EC). For further details, contact IMC  
Networks.  
Class 1 Laser product, Luokan 1 Laserlaite,  
Laser Klasse 1, Appareil A’Laser de Classe 1  
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this  
symbol on product or packaging must not be disposed of with unsorted municipal  
waste. This symbol indicates that the equipment should be disposed of separately  
from regular household waste. It is the consumer’s responsibility to dispose of this  
and all equipment so marked through designated collection facilities appointed by  
government or local authorities. Following these steps through proper disposal and  
recycling will help prevent potential negative consequences to the environment and  
human health. For more detailed information about proper disposal, please contact  
local authorities, waste disposal services, or the point of purchase for this equipment.  
4
 
19772 Pauling • Foothill Ranch, CA 92610-2611 USA  
TEL: (949) 465-3000 • FAX: (949) 465-3020  
© 2010 IMC Networks. All rights reserved.  
The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any  
errors that may appear in this document. McPC-Gigabit is a trademark of IMC Networks. Other brands or product names  
may be trademarks and are the property of their respective companies.  
Document Number 55-80900-00 B1  
February 2010  
 

Graco Inc Paint Sprayer 130 Convertible User Manual
H2O Audio Carrying Case S2 1A2 User Manual
Harbor Freight Tools Impact Driver 92622 User Manual
Hotpoint Double Oven AHP37X User Manual
HP Hewlett Packard Computer Monitor D8911 User Manual
HP Hewlett Packard TV Mount 307153 002 User Manual
IBM Cordless Telephone 4900 User Manual
IBM Power Supply IBM UPS 10000XHV User Manual
IBM Projector CP X445 User Manual
Iiyama Computer Monitor B1702S User Manual